Technology of Placing gypsum tiles along with your hands

Gypsum tiles have to be laid properly, as not only the aesthetic look of decorative facing, but in addition the service quality of

this material will be dependent on the engineering of job. The product is more also universal, and it can be attached to plaster,

concrete, brick or gypsum board sheets, provided that the top layer of the base is even and has no flaws.

In the event the defects of this base are significant, it ought to be completely treated with primer, then a cement mortar is

created, which satisfies all of the cracks. Subsequently the surface should be repeatedly primed and dried. Primer therapy is

necessary to improve the bond between the tile and the wall. In this case, its makeup should select a particular, containing

elements which block the look of fungus and mold.

In the modern interior of the rooms most frequently used gypsum tiles, imitating natural brick or stone. To execute decorative

finishing your self, it’s essential first of all to select a scheme of tile placement and prepare a remedy. It’s very important to

pay attention to the reverse side of this substance. If its surface includes an embossed surface, then the glue should be placed

having an trowel, also if it’s even, then with a top notch one.

The technology of this job is as follows:

* A thin layer of glue is applied to the pre-prepared wall. It’s distributed over the bottom so it is possible to put 4-5 tiles.

Decorative cladding can be put either on plasterboard, also on putty.

* Glue the back side of the tiles with glue.

* Plaster components are pushed against the walls and their location is corrected. To align with the seams, it’s recommended to

use spacers.

* Finishing is performed in rows, each of which should be changed by half a tile. Facing is completed to the corners of this

space, then immediately get rid of any remaining mortar at the joints.

Drying the walls requires no longer than a day and needs a constant humidity and temperature inside the room. The final point in

the placing of gypsum tiles is the decor. To do this, the joints between the elements are full of a particular solution, the color

of which suits the brick.

Decorative imitation of brickwork around the walls will be carried out in the following ways:

* Cutting on the darkened surface of the seams of masonry with a bolt cutter along with your hands;

* placing of tiles under the brick:

* imitating the format and color of the side surface of one brick;

* Imitating a fragment of brickwork of several bricks.

The very best way to decorate”under the brick” will be the one that permits you to make a practical coating with the most look of

its similarity to natural masonry. All 3 strategies to execute this type of finishing functions fulfill the demands, but the

cutting of joints with a bolt will be labor-intensive and the formation of large amounts of dust, and so let’s consider more

typical ways.

The old finish is removed from the walls, and the surface, if needed, is leveled to eliminate the need to glue plaster onto a

thick layer of adhesive.

Combining such cladding with other types of interior finishes may be both systematic and done with no clear consistency,

chaotically, together with fake of indications of aging.

With the support of decorative gypsum tiles it is possible to mimic a lot of textures.

A lot of textures could be imitated with the help of decorative gypsum tiles.

The wall on which it is to be installed must have the following characteristics:

* Hardness and durability of the surface; * The lack of irregular locations and sharp sections;

* not any deformations.

Cosmetic tiles at the interior of this kitchen

Walls are created from a variety of materials, let’s break down the principles of installment.

When dealing with concrete, there’ll be no huge problems. It’s just necessary to take into account the porosity of this material.

Concrete, which has nearly no pronounced pores, should be treated with a good primer.

Mounting gypsum tiles concrete

Before beginning work on the setup of gypsum tiles onto the walls, it is worth checking the strength of this surface. After the

plaster does not fall off the wall and at the same time holds nicely, you can simply paint it using primer.

Mount the tiles on the painted concrete should not. The surface ought to be scratched, ensuring to misfire, then it should be

grouted and covered with a coating of plaster.

Nog geen reacties

Geef een reactie